FLSP Series Automatic Loading Raycus Laser Mild Steel Cutting Machine

EETO-FLSP series include both sheet cutting function and pipe cutting function. And different from the other sheet&pipe laser cutting machine, our pipe cutting extension can cut not only round pipe and square pipe, but also oval pipes! We have set two zero point on this model, so our sheet&pipe laser cutting machine can find the pipe center very fast and very easy to change different diameter pipes. And with the new design, you can upload the sheet plate very easily.

What`s special about the EETO FLSP family:

The following is a comparison of the EETO tube cutting front and rear chucks and the normal front and rear chucks:

                                    EETO chuck                                                                          Normal chuck                            

EETO front chuck	Normal front chuck
Combined two axes linkage and unidirectional adjustment, very easy to find the middle point.	Unidirectional adjustment, hard to find middle point and not precision.
Each axis has long stroke , which can change different diameter pipes very easy.	Short axis stroke, need to change or move claw one by one every time when change different pipes.
Adopt high quality teel,high strength and low weight, revolving speed up to 70r/min	Chuck`s weight is very heavy,revolving speed is within 30r/min
EETO rear chuck	Normal rear chuck
No matter square pipe or circular pipe, can adjust the gripper according to the pipe diameter.	For square pipe , have to loose claw then adjust it.
Diameter from 20 mm to 200 mm, it can automatically clamp the tube without adjusting the gripper.	Travel distance :20mm for each side .when diameter change more than 20mm, need to unload claw.
Small reduction ratio, high precision grinding teeth, speed up to 70 rpm, cutting sound clear and smooth.	The motor power is small, rotate speed is lower than 30rpm, with obvious noise.

In addition, the normal chuck`s  chuck adjustment need manual support, need at least two person to adjust it and very hard to get good precision.

We Use Advanced Tools To Control Precision On Every Installation Steps:

Machine installation is important for checking quality of a laser machine,especially motion parts installation,which is used for ensure running and cutting accracy,here we introduce you how we install our laser machine linear.

1.

Linear guide parallelism examination,our requirement≤±0.02mm

2.

Rack installation,accuracy lower than≤±0.02mm

3.

Parallelism check between two guides,our accuracy requirement≤±0.02mm

4.

Linear guide hardness and straightness detection,our requirement≤±0.02mm

Application Industry:

In the laser cutting machine industry, the laser cutting occupies an important position in industrial production. For most metal materials, regardless of their hardness, they can be cut without borders.

Mainly used in sheet metal processing industry, agricultural machinery industry, advertising industry, kitchenware manufacturing industry, etc. In addition to the most widely used industries of laser cutting machines, such as automobiles, aerospace, steel structure construction, elevator manufacturing, printing, etc., there are corresponding There is room for development, so the laser cutting machine will become the mainstream of future development.

          Automobile             manufacturing

Industrial manufacturing

Fitness equipment

Main parts:

      

           Raytools cuttiong head

Packaging and transportation:

1. We use wooden cases that meet international export standard
2. All the motion parts are lubricated  and covered with firm to avoide direct air contact and thus prevent getting rust.
3. The whole machine and parts are well packed and  fixed inside of the wooden case without moving or sliding inside.

4. The inner space of the wooden case will be made into vaccum to keep dry and the plywood case will be covered with waterproof cloth to stop rain drops or sea water from entering the wooden case

Our Services:

Warranty period: From the acceptance qualified date, the warranty period will be 1 (one) year, During warranty, free repair or parts replacement(except consumable parts.)

After the warranty:we will also provide favorable service of long term technical supports and spare parts. 

After warranty:we promise to keep parts inventory for each part of machine. And onsite and offsite service is always available upon your request.

During or after warranty, we are always ready to help, Your satisfaction is always our priorty

and

Our 24hours online service.

Onsite service.

Training in our facotry ,You are always welcomed to get trainning in our factory.

Q: What's the working area of our fiber laser cutting machine? 

A: Our standard working area is 3000*1500mm.But we can also do customized sizes as request.

Q: What's the laser power of our fiber laser cutting machine? 

A: Now our standard laser power include 1000W, 1500W, 2000W, 3000W, 4000W , 6000W and 8000W

Q: What materials can we cut? What's the cutting thickness of fiber laser cutting machine?

A: Fiber laser cutting machine can cut most metal materials, but generally used for cutting carbon steel and stainless steel. Cutting thickness is from 0.5mm to 28mm according to different laser power.

Q: How to install the fiber laser cutting machine?

A: We will send our technician to customer's factory for machine installation,commissioning and training.

Q: What are consumables of fiber laser cutting machine?

A: Generally include protection lens, cutting nozzle and ceramic body.

Q: If we need to cut work-piece with different height, is it available?

A: Yes, it can cut work pieces with different height.The focus length can be adjusted automatically.

Q: Can we cut both sheet plate and pipe in one machine?

A: Yes,our sheet and pipe laser cutting machine can do that.

Q: What's the delivery time?

A: Generally speaking,lead time is 30~50 working days after deposite received.

EETO laser sample display:

1mm stainless steel round pipe

1mm stainless steel square tube

Pattern tube cutting

1.5mm galvanized pipe bend splicing

Stainless steel fan

3D tree

Flowers and birds

Dragonfly

Partial Configuration table

Note: For more parameter information, please consult sales or customer service.

TECHNICAL DATAS:

Note: This cutting parameter is for reference only, and the latest data is subject to the company's provision.

More machine details：

We use higher precision grade YYC rack and

TBI Linear guide, the code on the rack can be

checked on the internet

Automatic Gas Control,oxygen can be automatically controlled.

Integrated lubrication, all the motion parts can be lubricated from this oil pump.

These are trailer that collect the cut-off workpieces

under the machine bed, you can directly pull it out after finishing cutting.

All the signal cables and components are

orderly distributed, and each cable has

linemark on it, it is convenient for maintenance

Each electrical cabinet will be installed with an air conditioner ,which makes sure the temperature inside the cabinet constant.

Welcome to EETO......